Hardwood Flooring Company Information
Retail & Flooring Information

 Copyright 2023


Hardwood Flooring



Laminate Flooring

Specialty Flooring

Imported Italian Tile

Indian Slate
Natural Stone Tile

Cork Flooring

Bamboo Flooring

Wood Vents
Wood Returns


Wood Stains
Finishes - Fillers



Installation Products


Hardwood Flooring Information 


The wood floor finish company
where experience makes the difference.

Smooth Seal Waterbased Sealer
? A one-component, waterbased sealer
? Has excellent open time to avoid lap marks
? Minimizes grain raise and can be screened within 1 to 2 hours
? Excellent base for Precision waterbased finishes

Technical Data:
USES: Precision SmoothSeal Waterbased Sealer is a one-component, waterborne sealer designed to provide an excellent base for use under Precision water-based finishes. This amazing product is quick drying, yet, has excellent open time to avoid lap marks. Precision SmoothSeal Waterbased Sealer minimizes grain raise while providing a deep base that can be screened within 1 to 2 hours of application.

SURFACE PREPARATION: Sand floor to bare wood according to NWFA / NOFMA specifications. Fill all cracks and holes with Precision Full Trowel Wood Filler or Precision Wood Patch. Final sanding should be done with 100 grit sandpaper or screen. Vacuum the entire floor as well as the adjoining areas. Sanded floors should be tacked with a lint-free cotton cloth. Repeat until all dust is removed. Block off any direct sources of sunlight hitting the floor. Do not use SmoothSeal over stains. Always abrade sealer coat prior to applying Precision waterbased finish.

MIXING: Rock container well until finish is evenly dispersed. Let container stand 10 minutes while bubbles disperse. Always strain previously opened containers since skin will develop after opening. Occasionally stir finish or rock container during application.

APPLICATION AND COVERAGE: For best results, the room and the product should be between 60?F to 80?F. Precision SmoothSeal Waterbased Sealer can be applied by waterborne T-bar type applicator, paint pad or block type applicator. Apply at the rate of 500 square feet per gallon. Allow to dry at least 1 to 2 hours* or overnight before applying the next coat. Only one coat of Precision SmoothSeal is needed. *Note: Low temperatures, high humidity, as well as cool damp
conditions will retard drying. Warm up area to recommended temperature or allow extra drying time.

T-BAR APPLICATION: Pour a 4" bead of material the length of the floor. Cut in the side with a paint pad. Pull the sealer in a snowplow method from end-to-end in the room. Always work with the grain of the wood. Swivel the applicator when 6" from the baseboard and stop in line with the finish bead or puddle. Rock the applicator to remove excess product then feather the turn mark. It is important to feather out all turn and stop marks. Coat the edges at the end of the room after the body of the floor. Touch up ends as you coat across the floor to feather out applicator stop marks. Edging prior to coating the field could result in picture framing (additional film). Add product as needed to maintain a uniform product bead. By changing the angle of the applicator head, the product can be repositioned to maintain a wet edge without pouring out excess material. The speed of walking during the application and the weight of the applicator can and will affect the thickness of material left on the floor. Continue this procedure across the floor and reduce the size of the bead as you near the exit from the room. Allow sealer to dry before screening.

CLEAN UP: Clean up applicators and equipment using soap and water.

PACKAGING: Gallon 4/Case

INGREDIENTS: Contains:Acrylic copolymer, ammonia, glycol ethers. SPECIFIC GRAVITY: 1.01
VOC: max 2 lb/gl per (225 gl) BOILING POINT: 212?F VAPOR DENSITY: (air=1) < 1



Copyright 2024 MCEnt