Hardwood Flooring Oil Based
The wood floor finish
where experience makes the difference.
||Easy Coat Polyurethane
• Excellent flow and leveling
• Makes the most difficult floor finish project simple
• Provides excellent protection to all residential and commercial
• Available in Satin, Semi Gloss, and Gloss
EZ-235 - SATIN
EZ-270 - SEMI GLOSS
EZ-290 - GLOSS
USES: Precision Easy Coat Polyurethane is an oil-modified finish
providing excellent protection to all residential and commercial
wood floors. Precision Easy Coat Polyurethane's excellent flow and
leveling makes the most difficult floor finish project simple.
Available in Satin, Semi Gloss, and Gloss.
Prior to applying Precision Easy Coat Polyurethane, sand the
floor according to NWFA / NOFMA specifications. Fill all cracks and
holes with Precision Full Trowel Wood Filler or Precision Wood
Patch. Natural finish floors should not be sanded finer than 100
grit sandpaper or screen. For stained floors, sand and edge with 100
grit sandpaper then hand sand edges using 60 to 80 grit sandpaper.
Vacuum the entire floor as well as the adjoining areas. Sanded
floors should be tacked with a lint-free cotton cloth dampened with
mineral spirits or paint thinner. Block off any direct sources of
sunlight hitting the floor. Seal the floor according to label
directions using Precision Quick Dry Sealer or Precision Penetrating
Stain in selected colors. Stains other than Precision stains must be
tested for compatibility. DO NOT apply Precision Easy Coat
Polyurethane over floors sealed with wax, non-drying oils, shellac
or stearated sealers.
Stains other than Precision Penetrating Stains must be tested for
DO NOT apply Precision Easy Coat Polyurethane over floors sealed
with wax, non-drying oils, shellac or stearated sealers.
Easy Coat will amber when applied over light colored floors.
Block off any direct sources of sunlight hitting the floor.
Wait 24 hours before allowing light traffic on final coat.
Maintain floor with routine vacuuming and Precision Wood / Laminate
Cleaner Spray according to directions.
Use felt floor protectors under all furniture.
DO NOT cover with rugs for two weeks.
DO NOT use cleaner or water for two weeks after final coat.
MIXING: Stir product before and, occasionally, during
application. Ensure that all ingredients are completely mixed. DO
NOT shake polyurethane product to avoid bubbles in finish.
APPLICATION AND COVERAGE: For best results, the room and the
product should be between 60ºF and 80ºF. Precision Easy Coat
Polyurethane can be applied with a natural bristle brush, lambs wool
applicator, short nap mohair roller, or a T-bar applicator at the
spread rate of approximately 500 square feet per gallon. Allow to
dry at least 8 hours* or overnight. When dry, abrade with a used 100
grit (or finer) screen or abrasive pad with fine sandpaper strips.
Be sure to hand sand all areas not reached with machine. Vacuum
floor thoroughly and tack with a lint-free cotton cloth dampened
with mineral spirits. Apply the next coat of polyurethane. For high
traffic areas, screen as above and apply additional coats. *Note:
Low temperatures, and/or high humidity will retard drying.
CLEAN UP: Clean applicators and equipment using paint thinner or
RECOATING EXISTING FLOORS: Clean the floor with Precision Wood /
Laminate Cleaner Spray according to label instructions. DO NOT apply
over floors with wax, oil, grease, shellac, or stearated sealers.
Abrade old finish with 100 to 120 grit screen. Prepare and apply
additional coats of Precision Easy Coat Polyurethane as previously
5 Gallon 1/Case
INGREDIENTS: Contains: Petroleum distillates, silicone dioxide.
This product contains a max 3.71 pounds of VOC per gallon of coating
Do not thin. Maximum vapor pressure is 2.00 mmHg at 68ºF. This
product is non-photo chemically
Hardwood Flooring Oil Based Finish Distributor,
Wholesale Hardwood Flooring, Wholesale Flooring Distributor Flooring,
Laminate Flooring Distributor, Wholesale Tile Distributor, Serving Limerick,
Philadelphia, PA, Pennsylvania, Delaware Valley, New Jersey, Delaware, MD,
19464, 610, 215, 302, 856, 717